DENMARK

World No.1 mitre cutting machine for over a century.

MORSO NFManual Notch Cutting Machine

CODE NO. 8015

  • MORSO – NFS (Nose width 6-20mm) / MORSO-NFL (Nose width 12-26 mm) The MORSO – NF is a foot operated notch cutting machine for cutting window bars, mullions, and cabinet front frames requiring haunch joints.
  • MORSO – NF leaves the cut surface of the wood perfectly smooth and accurate, requiring no further preparation before joining. The horizontal movement of the knife block is stepwise adjustable.
  • The fences, left and right, with the adjustable stops ensure correct work. The special lever system of the machine ensures a very easy operation. Twin return springs automatically bring the knives back to starting position.

Comes equipped with:

  • Safety guards
  • Waste chute
  • 6 sliding longitudinal stops fences on both the left and right side
  • 2 nose knives
  • 1 pair of side knives

Technical Specifications:

MORSO NFS

Code no. 8015S

MORSO NFL

Code no. 8015L

Nose width (MORSO-NFS) 6 – 20 mm 12 – 26 mm
Cutting width max. 70 mm (3”) 70 mm (3”)
Cutting height max. 160 mm (5 ½”) 160 mm (5 ½”)
Fences, left & right * 1500 mm (60”) 1500 mm (60”)
Extension tables, left & right 750 mm (30”) 750 mm (30”)
Weight 100 kg 100 kg

* Upon request: Fences 2500mm (100”) supplied with extra extension table and supporting leg

MORSO NFX Manual Notch Cutting Machine

CODE NO. 8020

  • MORSO – NFXS (nose width 6-20 mm)
  • MORSO – NFXL (nose width 12-26 mm)
  • The MORSO – NFX is a foot-operated notch cutting machine for cutting window bars, mullions, and cabinet front frames requiring haunch joints. MORSO – NFX leaves the cut surface of the wood perfectly smooth and accurate, requiring no further preparation before joining. The horizontal movement of the knife block is stepwise adjustable. The fences, left and right, with the adjustable stops ensure correct work. The special lever system of the machine ensures a very easy operation. Twin return springs automatically bring the knives back to starting position

To compare MORSO – NFX with a moulding machine the following points must be considered:

  • A cleaner and more constantly accurate cut will be produced with MORSO – NFX.
  • The MORSO – NFX produces no dust and therefore requires no extraction.
  • The MORSO – NFX requires less than 15 minutes to change the cutting blades, to the set-up, and to the positioning of the stops
  • As the blades wear, the 46 angle remains unchanged, ensuring consistently accurate joints.
  • The MORSO – NFX cuts plastic, all kinds of wood including MDF
  • Safety guards
  • Waste chute
  • 6 sliding longitudinal stops fences on both the left and right side
  • 2 nose knives
  • 1 pair of side knives

Technical Specification:

MORSO NFXS

Code no. 8020S

MORSO NFXL

Code no. 8020L

Nose width (MORSO-NFS) 6 – 20 mm 12 – 26 mm
Cutting width max. 205 mm (8”) 205 mm (8”)
Cutting height max. 160 mm (5 ½”) 160 mm (5 ½”)
Fences, left & right * 1500 mm (60”) 1500 mm (60”)
Extension tables, left & right 750 mm (30”) 750 mm (30”)
Weight 100 kg 100 kg

* Upon request: Fences 2500mm (100”) supplied with extra extension table and supporting leg

MORSO NEHPneumatic Notch Cutting Machine

CODE NO. 8016

  • MORSO – NSEH (nose width 6-20mm) / MORSO – NLEH (nose width 12-26mm)
  • MORSO – NEH an electric hydraulic guillotine for cutting window bars, mullions, and cabinet front frame requiring haunch joints.
  • MORSO – NEH is a machine designed for medium High Volume production – the noise level is 70 db. The MORSO – NEH Will cut plastic, all kinds of wood including MDF. The MORSO – NEH Operates in principle the same as MORSO – NF.

To compare MORSO – NEH with a moulding machine the following points must be considered:

  • A cleaner and more constantly accurate cut will be produced with MORSO – NEH.
  • The MORSO – NEH produces no dust and therefore requires no extraction.
  • The MORSO – NEH requires less than 15 minutes to change the cutting blades, to the set-up, and to the positioning of the stops.
  • As the blades wear, the 46 angle remains unchanged, ensuring consistently accurate joints.

MORSO – NEH is supplied with the same standard equipment as the MORSO – NF plus it has:

  • Automatic cutting cycles for both large and small work pieces – which means that the machine always does the thing cut which is very important
  • Adjustable length of stroke (2 positions) – when using the lowest cutting position the cutting cycle of two cut only takes between 1 and 1.5 seconds.

Technical Specification

MORSO NSEH

Code no. 8016S

MORSO NLEH

Code no. 8016L

Nose width (MORSO-NSEH) 06 -20 mm (1/2”-1 1/ 1/8”) 12-26 mm (1/4” – 3/4”)
Cutting width max. 70 mm (3”) 70 mm (3”)
Cutting height max. 140 mm (5.5”) 140 mm (5.5”)
Fences, left & right * 1500 mm (60”) 1500 mm (60”)
Extension tables, left & right 1000 mm (40”) 1000 mm (40”)
Pumping capacity 7 liters / min 7 liters / min
Working pressure 80 bar 80 bar
Power transmission 660 kgs (1455 lbs) 660 kgs (1455 lbs)
Tank contents 8 ltrs. (2 gal.) 8 ltrs. (2 gal.)
Motor three phase or single 1.1 kW 1.1 kW
Net weight 145 kg (319.7 lbs) 145 kg (319.7 lbs)

* Upon request: Fences 2500mm (100”) supplied with extra extension table and supporting leg

MORSO NXEH Pneumatic Notch Cutting Machine

CODE NO. 8022

  • MORSO – NXSEH (nose width 6-20 mm)
  • MORSO – NXLEH (nose width 12-26 mm)
  • MORSO – NXLEH an electric hydraulic guillotine for cutting window bars, mullions, and cabinet front frame requiring haunch joints.
  • MORSO – NXLEH is a machine designed for medium-high volume production, the noise level is 70 db. The MORSO – NEH Will cut plastic, all kinds of wood including MDF

To compare MORSO – NXSEH with a moulding machine the following points must be considered:

  • A cleaner and more constantly accurate cut will be produced with MORSO – NXLEH.
  • The MORSO – NXLEH is almost silent by comparison
  • The MORSO – NXLEH produces no dust and therefore requires no extraction.
  • The MORSO – NXLEH requires less than 15 minutes to change the cutting blades, to the set-up, and to the positioning of the stops.
  • As the blades wear, the 46o angle remains unchanged, ensuring consistently accurate joints.

The MORSO – NXLEH is supplied with the same standard equipment as the MORSO – NXLEH plus it has

  • Automatic cutting cycles for both large and small work pieces – which means that the machine always does the thing cut which is very important
  • Adjustable length of stroke (2 positions) – when using the lowest cutting position the cutting cycle of two cut only takes between 1 and 1.5 seconds.

Technical Specifications

MORSO NXSEH

Code no. 8022S

MORSO NXLEH

Code no. 8022L

Nose width (MORSO NXSEH) 6 – 20 mm (1/2” -1 1/ 1/8”) 12-26 mm (1/4” – 3/4”)
Cutting width max. 200 mm (8”) 200 mm (8”)
Cutting height max. 145 mm (5.5”) 145 mm (5.5”)
Fences, left & right * 1500 mm (60”) 1500 mm (60”)
Extension tables, left & right 1000 mm (40”) 1000 mm (40”)
Pumping capacity 7 liters / min 7 liters / min
Working pressure 80 bar 80 bar
Power transmission 660 kgs (1455 lbs) 660 kgs (1455 lbs)
Tank contents 8 ltrs. 8 ltrs.
Motor three phase or single 1.1 kW 1.1 kW
Net weight 141 kg 141 kg

* Upon request: Fences 2500mm (100”) supplied with extra extension table and supporting leg

MORSO F Mitre Cutting Guillotine

CODE NO. 1011

The farmer’s favorites in the world over since 1911. A foot operated mitring
machine from Danlist of Denmark

  • Clean cut needs to finishing after cutting
  • Cuts double mitre at 45 and single mitre up to 900
  • Nice operation results in no dust environment
  • No compressor or electricity needed
  • Easy operation through special Lever system
  • Sliding scales ensures perfect measurement of frames
  • Accurate repeat work and production

Comes equipped with:

  • Safety guards
  • Waste chute
  • Sliding measurement stop
  • Measuring scale upto 1500 mm

OPTIONAL ACCESSORIES

  • MORSO Scale set of 3 pcs comprise of long divided Bean, short beam and stop being. code number: 1006
  • Divided Bean set of 2 pieces. set short and long beam. Code no. 1015
  • Stop Beam code no. 1017
  • Left hand support table: MORSO extension table can be installed on the MORSO F, MORSO FC and MORSO H metering machine. The MORSO extension table is 770 mm long. Code no. 1007
  • Stop Block code no. 1009

Technical Specifications

Double mitre 450
Single mitre 900
Cutting width max 100 mm (4”)
Cutting height 160 mm (6 1/3”)
Measuring scale up to 1500 mm (60”)
Weight 96 kgs Approx.

MORSO EH Hydraulic Mitre Cutting Machine

CODE NO. 1012

  • MORSO – EH is a fully automatic, electric/ hydraulic mitring machine with a two hand release button in. This makes the machine absolutely safe, as it is impossible to operate the machine, and touch the knives in the same times
  • With MORSO – EH you achieve the clean smooth cut by automatically cutting off the section in two cuts, as long as both push buttons are activated at the same time
  • The cutting time varies from 1 sec. and up, depending on the thickness of the workpiece. Having finished the cutting, the nice block automatically returns to the starting position.
  • The starting position (horizontal movement) is adjusted according to the width of the moulding, and MORSO – EH will automatically cut the workpiece bit by bit.
  • The vertical movement of the knife block is also adjustable with three different Heights. Pos. 1 for small world peace, Pos. 2 for medium size workpieces and Pos. 3 for very thick pieces.

Comes equipped with:

  • Front safety guide
  • 40 mm high rebate support
  • Waste chute
  • Second stop
  • Measuring scale upto 1500 mm

The MORSO – EH is excellent for repetition work as:

  • It is as fast as double mitre saw.
  • The cutting waste dropped into a waste chute.
  • The working procedure create no dust
  • The noise level is below 70 DB

Technical Specifications

Double mitre 450
Single mitre up to 900
Cutting width max 100 mm (4”)
Cutting height max 180 mm (7”)
Square cutting 70/70 mm (2 ¾”)
Measuring scale upto 1500 mm (60”)
Motor, three phase 1,1 kw
Pumping capacity 71/min
Working pressure 80 bar
Square Cutting 70/70 mm
Power transmission 660 kgs
Tank contents 8 ltrs.
Net weight 135 kg

MORSO EHXL Hydraulic Mitre Cutting Machine

CODE NO. 1022

World’s only mitring machine which can cut upto 150 mm wide moulding

  • MORSO EHXL Is fully automatic electric / hydraulic mitring machine, with a noise level below 70 DB – the perfect machine to cut picture mouldings for production of wooden, plastic and MDF mouldings.
  • In principle MORSO EHXL does the same work as the MORSO F, but with the MORSO EHXL you have your work done automatically by pushing two push buttons.
  • The MORSO EHXL is safe to operate as you must activate both push buttons at the same time to have the machine work, and therefore you cannot get your fingers underneath the knives. With the MORSO EHXL you can do production work all day long.
  • The MORSO EHXL is available with three phase motor, voltage to your requirement.
  • The MORSO EHXL is available with single phase motor.
  • Due to its design – the MORSO EHXL is ideal for female and elderly workers. No effort is require to cut the moulding due to the dual hand operation system.

Comes equipped with:

  • Front safety guard
  • Waste chute
  • Second stop
  • Measuring scale up to 1500 mm
  • Adjustable & automatic rebate support & clamping cylinders
  • Sliding longitudinal stop
  • Two hand release operation
  • Extension table for the left side
  • Adjustable fences
  • Supporting legs

WARRANTY : 1 YR [PROVIDED CORRECT USE AND MAINTAINANCE]
* warranty doesn’t cover the tear & wear such as blades, spring & measuring scales.

Technical Specifications

Double mitre 450
Cutting width max. 150mm
Cutting height max. 250 mm
Deluxe Measuring scale up to 2500 mm
Motor, three phase 1.5 kw, 3.3 amps
Net weight 278 kg
Pumping capacity 11.2 liters / min
Working pressure 80 bar
Power transmission 660 kgs
Tank contents 8 ltrs

MORSO PME 100 Profile Milling Machine

CODE NO. 8085

  • The profile Milling Machine is for reversed profiling of cross-cut timber. The work piece is placed against the end stop, and the reversed cutting is done by moving the table manually from the left to the right ensuring a tear free cutting.
  • Manually operated
  • Manual movement of routers
  • Manual clamping of work piece

Equipment:

  • 2 motors for milling, 1.5kw, 400v, 1200 rpm.
  • One motor turns clock wise and the other motor turns anti clockwise
  • Safety Guard
  • Emergency stop

Cross Cutting Saw:

  • Makita Unit.
  • Digital Read Out.The digital read out is encoded with sur-measurement do that the work piece has the correct length after the milling
  • 1500 mm rail for standard cutting length Extra length on request

Blades

The Original accessories made by Hoffmann offer technical solution for different applications. Special accessories such as material support, additional clamping devices.

  • MORSO Standard ** Blades are specially produced using high quality steel with hardness of HR 64 giving the blades 6 – 7 times longer life than all other brands.
  • MORSO Reversible Blades has been introduced in MORSO machine
  • This blade can cut up to 37 mm from both sides and saves on your blade sharpening cost.

Glazing Fence Fixture – Code No. 5107

Glazing Fence Fixture – Code No. 5107

Glazing Fence Fixture – Code No. 5107)

  • 20 mm nose knife
  • Size of nose knife is available in metric and inches from 4 mm up to 26 mm
  • Larger sizes upon request
  • Constantly accurate cut, No gaps will be seen

GERMANY

High-quality woodworking machines with patented dovetail keys.

Applications of Hoffmann Keys

World’s only mitring machine which can cut upto 150 mm wide moulding

The potential range of use for the Hoffmann key in all areas of the woodworking industry is enormous. For each application select the appropriate key.It is simple brilliant and incredibly simple.

Picture frames 8 mm width

Cornices Crown mouldings

Picture frames panels glazing frames

Lighting strips Lighting screens Mouldings and sub-structures

Georgian bars Glazing Xassettes Curved Frames

Door linings Frames Building frames

Plinths Drawers Boxes,shelves vision panels

Hand rails(profiled)Banisters

Circular handrails

Window frames Wood / Alu Plastic

Window sash Wood / Alu Plastic

Post/beam Glass facades Conservatories Pre-fab houses

HOFFMANN X LINE 20 Manual Dovetail Routing Machine

CODE NO. 5003

  • Portable and flexible bench – top machine, for routine a single dovetail slot with each machine cycle
  • Hoffmann Key sizes W-1/2/3. Most of the relevant accessories can be used on this machine
  • Option: Twin version with a double spindle gearbox to produce two dovetail slots machine cycle

Function:

Position the work-piece on the centre-fence and move according to the profile width. Pull down the handle to clamp the workpiece. Continued pressure raises the router carriage to the preset depth. When the handle is returned, the carriage lower to its composition and the workpiece is released. The motor switches on and off automatically

Machine components

  • Motor
  • Router depth setting
  • Micro switch for motor

Operating elements

  • Router depth setting
  • Work-piece clamping
  • Chip – breaker

Technical Specifications

Power supply 1ph/N/PE 230 V 50/60Hz 0.5 kW
Motor 1 x 530 W
Motor speed 29000 1/min
Control / work – piece clamping manual / manual
Height capacity 110 mm
Routing depth 0-80 mm
Extraction port Ø60 mm
Hoffmann Key sizes W-1/2/3
Dimensions W/D/H 600/540/770 mm
Weight 19 kg

HOFFMANN X LINE 20DB Manual Dowel Boring Machine

CODE NO. 5009

  • Portable and flexible bench – top machines for dowel boring
  • Two dowel holes can be done in one machine cycle

Function:

Position the work-piece on the centre-fence and move according to the profile width. Set the height of the motor as per the desired depth. Pull down the handle to clamp the workpiece. Continued pressure pushes the drill carriage into the work piece up to the preset depth. When the handle is returned, the carriage retracts to its home position and the workpiece is released. The motor switches on and off automatically.

Technical Specifications

Power supply 1ph/N/PE 230 V
50/60Hz 0.5 kW
Motor 1 x 1000 W
Motor speed 29000 1/min
Work – piece clamping Manual
Height capacity 110 mm
Drilling depth 10-30 mm
Dust extraction duct Ø 60 mm
Dowels – drills Ø 8 mm
Dimensions W/D/H 600/540/700 mm
Weight 29 kg
(with 10 mm cutter)

HOFFMANN MU3 Manual Dovetail Routing Machine

CODE NO. 5001

  • Transportable and adaptable bench – top machine, to route a single dovetail slot with each machine cycle for Hoffmann Keys size W-0/-1/-2/-3/-4
  • Heavy duty dovetail routing machine with casted base

Function:

  • Position and Secure the fence plate and lay the workpiece against it. Buy drawing down the hand Lever, the workpiece is clamped and the motor starts. Continued pressure on the lever raises the router unit through the work-piece and to the preset routing depth. When the hand Lever is returned to its original position motor switches off automatically and the routed work-piece is released.
  • On the model version MU 3-D the routing position, as well as the routing depth are digitally displayed to the accuracy of 1/10th mm.

Additional features

  • Optimized height capacity
  • Increased routing depth
  • Hand level with ball bearing guide

Operating elements

  • Angle fence
  • Butt stop fence
  • Internal fence

Technical Specifications

Power supply 1ph/N/PE 230 V 50/60Hz 1.0 kW
Motor 1 x 1000 W
Motor speed 34000 1/min
Work – piece clamping Manual
Height capacity 130 mm
Routing depth 0-85 mm
Extraction port Ø50 mm
Hoffmann Key sizes W-1/2/3/4
Dimensions W/D/H 740/650/835 mm
Weight 32 kg

HOFFMANN MU-2-H Horizontal, Manual Dovetail Routing Machine

CODE NO. 5010

  • Portable and flexible bench – top machine to router a single horizontal dovetail slot per machine cycle. Dovetail key sizes W-1/2/3/4.

Function:

  • The workpiece is positioned against the centre fence and the routing length (left & right) is set. By pressing the pneumatic foot pedal the workpiece is clamped.
  • The motor is switched on manually and the motor unit is drawn to the set router length. When the part is routered the unit is brought to the middle position, motor switched off and the workpiece is removed after releasing the foot pedal.

Technical Specifications

Power supply 1ph/N/PE 230 V
50/60Hz 1.0 kW
Pneumatic 6 bar
Motor 1 x 1000 W
Motor speed 34000 1/min
Control Manual
Work – piece clamping Pneumatic
Height capacity 110 mm
Routing depth H 0-80 / L 0-250 mm
Hoffmann Key sizes W-1/2/3/4
Dimensions W/D/H 700/600/500 mm
Weight 33 kg
(with 10 mm cutter)

HOFFMANN PU 2-32-100 Pneumatic Dovetail Routing Machine

CODE NO. 5005

  • Freestanding version with solid cast table and large working surface at comfortable working height
  • With two routing units to produce two dovetail slots in size of W-1/2/3 and option W-4
  • Infinitely adjustable router cross-centers from 32 mm 200 mm

Function:

  • The semi-automatic machine cycle is actuated by pressing the foot-pedal. The positioned workpiece is clamped and the units router to the preset depth and then return to their home position. The work-peace is then released. The centre fence position and the routing depth are selected manually. The router cross-centres are positioned manually with the aid of a lead screw and digital counter.

Technical Specifications

Electrical Power supply 1ph/N/PE 230 V 50/60Hz 2.0 kW
Pneumatic connection 6 bar
Motor 1 x 1000 W
Motor speed 34000 1/min
Control/ work – piece clamping Pneumatic
Work-piece Height 210 mm
Routing depth 0-115 mm
Extraction port 0-100 mm
Hoffmann Key sizes W-1/2/3/4 optional
Dimensions W/D/H 800/750/1500 mm
Weight 220 kg

HOFFMANN PP 2-NC Automatic Dovetail Routing and Dowel Boring Machine

CODE NO. 5006

  • NC Best machine for preparing the frame and corner joints in building components. E.g. in window and door production
  • This machine routers the dovetail slots (Hoffmann Keys W-1/2/3) and drills the dowel holes from 8 mm
  • Variable positions of the slots and dowel holes horizontally, vertically or in a combination of both
  • Moreover the free positioning over the entire workpiece is possible
  • Typical example choice would be 2x dowel holes and 3 dovetail slots. Working capacity over the mitre cut.

Function:

  • Enter all the component data and processing parameters directly on the 5.7” colour touch screen panel. Transfer the data via USB connection is also available.
  • Programs can be saved and quickly called up, with 100 program spaces of routing and boring available.
  • Multilingual menu/ operator guidance. Simultaneous processing of two work pieces per machine cycle. Corner joint with her choice of angle from 0 o to 67 o or but joint at 90o. For node connections they are butted and locked.

Technical Specifications

Power supply 230 volts, 3 phase, 4KW
Air supply 90 psi – 6 bar
Router motor 2 x 1000 watt – 30000 rpm
Drilling motor 2 x 1000 watt – 10000 rpm
Router head collet 1/4″
Drilling head collet 8 mm
Operation PLC controlled
Display 5.7” Color touch screen
Max. horizontal travel 8 1/4″ (210 mm) L+R
Max. material height 5 1/2″ (140mm)
Max. boring depth 1 3/16” (30mm)
Available router bits W-1, W-2, W-3
Available drill bits 8mm, 10mm, 12mm
or per customers’ requirements
Dimensions W/D/H 47 1/4″ / 51 1/8” / 59”
Weight 564 lbs.

HOFFMANN MS 35 SF Double Mitre Saw and Dovetail Routing Machines

CODE NO. 5007

  • Two clean precision mitre cuts to an exact length, with or without routed slots, in one machine cycle
  • When both pieces are to be joined together or in a frame, then they can be prepared with one or two dovetail slots in precise positions in the cut faces for joining with Hoffmann Keys.
  • Suitable for workpiece sizes maximum 90 x 90 mm.
  • Hoffmann key sizes W-1/2/3. Ideal for cutting profiles for glazing beads, cornices, plinths etc. in wood, aluminium all plastic at 45 o
  • It can also be used solely as Double Mitre Saw, to cut to length profiles such as Glazing beads, cornices, plinths, etc. in wood, aluminum and plastic at 45 o angles.

Function:

  • The work-piece is laid on the table and positioned for cutting.
  • The start button is pressed to begin the machine cycle and profile is clamped.
  • Both saw unit cycle from above to make the metre cuts.
  • The parts remain clamped whilst the tables open to allow the router units to rout one or two dovetail slots.
  • The machine table close and the finished work piece is removed
  • The profile is fed through the machine till the cut face is against the digitally positioned fence stop. The next machine cycle begins.
  • The measurement of the profile length is determined by manual positioning of the fence stop and reading the digital display. The sequence of the router units follows automatically.

Technical Specifications

Power 230 volts, 3P, 20 Amps
Air supply 90 PSI
Router heads 2 x 500 Watt – 24000 RPM
Saw heads 2 x 2 1/2 HP, 3470 RPM
Saw blades 350 mm diameter | carbide tipped
Router bits W-1, W-2, W-3
Cutting capacity 3 1/2″ width (89mm)
3 1/2″ thickness (90 to 90 mm)
Max. routing height 2 3/4″ ( 70 mm)
Cutting angle 45 degree fixed
Minimum length 3” ( 75 mm)
Maximum length 96”, longer length optional
Controls electronic operation with PLC
Dust collection 2 x ports, 4.7” diameter, 400cfm
Dimension W/D/H 587/8” / 371/2” / 633/4”
With table extensions 220”
Weight 1496 lbs.

Dovetail Routing Machines

The Original accessories made by Hoffmann offer technical solution for different applications. Special accessories such as material support, additional clamping devices.

Internal fences set, complete – Code No. 5101

Extension Fence, Fence guide extension – Code No. 5102

Collets – Code No. 5103-6, Code No. 5103-8
(collet – 6.00mm, collet – 8.00mm)

Router Bits TCT

Glazing Fence Fixture – Code No. 5107

Face Frame Jigs – Code No. 5106

Code No: CW 1060 W-1, 6mm Router HM

Code No: CW 2060 W-2, 6mm Router HM

Code No: CW 3060 W-3, 6mm Router HM

Code No: CW 4060 W-4, 6mm Router HM

ITALY

Global leaders of underpinner machines,double mitre saws,flexible and hard tabs and v-nail fasteners.

ALFAMACCHINE T 400 Double Mitre Saw

CODE NO. 3769

  • Every user of a double mitre saw, seeks the perfect blades. The blades are made of high strength Steel. Vertical movement of double mitre saw with two blades fixed at 45 o angle is useful for cutting picture, furniture, window and door frame, made of wood, plastic and aluminum. Pneumatic device allows quick backstroke Of blades and low air consumption.
  • Equipped with adjustable speed of blade’s decent.
  • Out feed measurement table and gorge.
  • Pneumatic device allows quick backstroke of blade and low air consumption

Add on Accessories

  • Extension gauge and table (out feed 1200 mm)Code no. 2015
  • Small blade flangesCode no. 2016
  • Mechanical adjustment of blade stroke going upCode no. 2017
  • Mist cooling system for cutting aluminumCode no. 2018
  • Dust collector unitCode no. 2019
  • Horizontal clamp systemCode no. 2020

Extra set of blades for
Circular Saw

  • Aluminum Code no. 2012
  • Plastic Code no. 2013
  • Wood Code no. 2014

Technical Specifications

Maximum cut blade 400 mm dia, weight- 100 mm, height- 80 mm
Max. production/ hour 600- 700 cuttings
Motors 2 nos. 2 HP, 2800 RPM
Hole suction 80 mm dia
Square cutting 65 mm / 65 mm
Electric power supply 380- 420 V 3 phase 50 Hz
Power absorption 3kw
Pneumatic feed 100 PSI
Air consumption 8 NI / 5 bar / 73 PSI
Weight 500 kgs approx.
Overall dimension 1000 x 1000 x 1800 (H) mm

ALFAMACCHINE U300 Pneumatic Under Pinner

CODE NO. 0826

  • The MINIGRAF M3 is a bench – top frame assembly machine 6
  • Most popular model with the custom farmer
  • It is compact and well-constructed, built for many years of trouble free operation
  • With this machine, for farmer sets the front and back stops for V-nail insertion.
  • The frame is then mo ved across the nail had and V-nails can be driven or stacked anywhere along the frame joint
  • The V-nail insertion is made through the use of a pneumatic pedal

Technical Specifications

Moulding thickness 6 mm to 80 mm
Moulding width up to 100 mm
Pneumatic feed 3 + 6 bar
Weight 32 kgs approx
Dimension 480 x 300 x 300 mm

ALFAMACCHINE U300P Production Under Pinner

CODE NO. 0827

  • MINIGRAF M4 has been designed for production of small and medium sized frames
  • The MINIGRAF M4 is equipped with a V-nail driver assembled on a movable carriage control pneumatically by the operator
  • The three positions version allows the V-nail insertion at three separate positions one after the other

Technical Specifications

Moulding thickness 6 mm to 80 mm
Moulding width up to 125 mm
Pneumatic feed 4 + 6 bar
Weight 36 kgs
Height of working bench 130 mm
Overall dimension 640 mm x 350 x 470 mm
Max. nail positions 3

ALFAMACCHINE U600 Multichannel Under Pinner

CODE NO. 0830

  • The New MINIGRAF MP multi-channel is the evolution of our standard memory program machine, it has the same ease of use, speed, and precision of assembly
  • The multi-channel version has five different nail magazines containing V-nails of different Heights, 5 mm, 7 mm, 10 mm, 12 mm and 15 mm. In the same working style, the Operator can insert and / all stack different V-nail heights in several different positions. The memory program technology is “state of the art” allowing you to store unlimited different programs and can also be downloaded to the machine by using a PC
  • Once this information is stored, the operator then selects the next frame to be used, either by using the keypad or with the optical barcode scanners
  • The machine automatically adjusts itself and production can restart immediately
  • The memory program multi-channel does not have an equal in terms of ease of use, programming, or rapid assembly of your products (it take 1 second to insert 2 nails in two different positions at a distance of 3 entimetre between the nail positions)

Technical Specifications

Frame thickness min – max. 5 mm to 80 mm
Frame width min – max 10-100 mm
Max. dist. among V-nails 140 mm
Storage capacity n. 220 x 5
Pneumatic speed 6 + 7 bar
Air consumption 5 bar
V-nails size 5-7-10-12-15 mm
Weight about 135 kg
Working bench height 960 mm
Overall dimensions 770x770x1500mm

QuickWood F3 Pneumatic Hand Sanding tool

CODE NO. QMF3

ONE HAND TOOL – SMALL DIAMETER, LIGHT WEIGHT

  • Model F3 is a pneumatic light weight one – hand tool for Quick Flex with a max. diameter of o 200 mm
  • Due to the low weight and relatively small diameter one can easily come into corners, profiles and other difficult spots.
  • With a coarse grit of Quick flex one can even do rough wood sanding

Comes with:

  • Removable dust shield study motor with Teflon vanes a hexagonal axle for direct power transfer.
Coarse Sanding Medium Sanding Finish/Sealer Sanding
Code: QF204050 -Quick flex 20 Seg/40 mm P 80 P120/P150/P180 P240/P320
Code: QF284050 -Quick flex 28 Seg/40 mm P 80 P120/P150/P180 P240/P320
Code: QF206550 -Quick flex 20 Seg/65 mm P 80 P120/P180 P240
Code: QF286550 -Quick flex 28 Seg/65 mm P 80 P120/P180 P240

Technical Specifications

Air motor, rpm, max 1700
Air pressure, bar, max 6
Air consumption, I/Sec. 5
Output, W 170
Number of Quick Star 20
Working width, quick flex, mm max 50
Length of spindle, mm 50
Net weight, kg 0.7
Gross weight, kg 1,0

QuickWood F6 Pneumatic Hand Sanding tool

CODE NO. QMF6

ONE HAND TOOL-FOR SANDING – SEALER SANDING

Model – QMF6 is a pneumatic 1-handmachine for all the sanding tools in Quick wood system. The low weight and powerful motor is your guarantee for efficient work. The F6 tool is particularly suitable for sanding for sanding, of the raw wood & for sealer finishing sanding of: Kitchen cabinets, frames windows, also used for the polishing of wax or the strepping of old windows & Furniture.

Coarse Sanding Medium Sanding Finish/Sealer Sanding
Code: QF284075 -Quick flex 28 Seg/40 mm P 80 P120/P150/P180 P240/P320
Code: QF286575 -Quick flex 28 Seg/65 mm P 80 P120/P180 P240
Code: QN75QD250 -Quickdisk + Tynex Ø 250 P 80 P120/P150 P240

QuickWood F15 Pneumatic Hand Sanding tool

CODE NO. QMF15

TWO HAND TOOL – FOR SANDING – EDGES IN PILE AND LARGE SURFACES

Quick wood system model F15 has the following advantages:

  • Same recommendations as for F6
  • Delivered with air hose and dust shield
  • Trigger which gives a possibility for slow start
  • Sturdy air motor with Teflon vanes
  • Hexagonal shaft for direct power transfer
  • Low working weight
  • Suspension point
  • Easy to turn direction of rotation

Model F15 is a pneumatic 2-handmachine for 15 quick discs or alternative sanding tools from Quickwood system

The relatively low weight and powerful machine guarantee a high production rate.Model F15 is particularly suitable for:

  • Edges of panels in pile
  • Entrance and interior doors
  • Large pieces of furniture
  • Coffins
  • Large profile
  • Stacked edges
  • Assembled furniture
Coarse Sanding Medium Sanding Finish/Sealer Sanding
Code: QF4440200 -Quick flex 44 Seg/40 mm P 80 P120/P150/P180 P240/P320

F6 Red

F15 Red

Code no. QMF6 Code no. QMF15
Air motor, rpm, max 900 900
Air pressure, bar, max 6 6
Air consumption, I/Sec. 4.8 9.6
Output, Watt 190 400
Number of Quick Descs / QN 6/3 15/7
Working width, quick flex, max. 75 150
Length of spindle, mm 85 200
Working weight, kg 1.1 3.5
Shipping weight, kg 2.0 4.2

QuickWood System CD-2-300 Compact 3 sided Low Cost

CODE NO. QMCD 2300

FINISHING AND SEALER SANDING OF OBLONG ITEMS

  • Module 300 with 2 motors (2 x 0.55 kw)
  • Infinitely variable adjustment by frequency alternator (350 – 1150 rpm)
  • Height adjustable 0-100 mm by hand wheel
  • Dust collection with 2 x 90 mm duct
  • Roller conveyor, 1441 mm long with PVC rollers, working height 852 mm.
  • Conveyor motor 0.37 kw with 7 m/min. (optional with adjustment from 3-18 m/min)
  • Pressure rollers in front of, between and behind the spindles.
  • Working width 300 mm.
  • Removable shafts.
  • Optional side sander in the right side
  • Optional side sander in the left side to be adjusted in all angles
  • Prepared for all QuickWood tools

Technical Specifications

Dimensions of workpieces

Height max. mm 100
Width max. mm 300
Length min. mm 380
Through feed speed, m/min 7
Spindle speed, rpm 350 – 1150
Spindle length, mm 300
Numbers of spindles 2
Diameter of tools, max., mm 300
Total number of Quick- Disc 48
Main motor, kw 2 x0.55
Conveyor motor, kw 0.37
Dust collection duct, mm 2 x 90
Dust collection m3/h 1500
Net weight kg. appr. 260

QuickWood System CD-4-200 Automatic Brushing Machine

CODE NO. QMCD4 200

For a perfect sanding and brushing

  • Rotating horizontal axes with adjustable speed by electronic inverter
  • Pressure rollers loaded with springs that ensure the sealing of workpieces during transport
  • Motorized roller conveyor with variable speed via invertor
  • Easily removable and inter changeable axes
  • Manual inclination of all axes
  • Roll feed or carpet of choice

Applications

  • Profiles
  • Rods
  • Frames
  • Uprights and transoms of doors and windows beads

Advantages

  • Reduced dimensions
  • Quality – price ratio of maximum convenience
  • Modular construction
  • Additional work units on all four side

Technical Specifications

CD 2 / CD 4 / 200

Height max. 100 mm
Width max. 300 mm
Length min. 380 mm
Horizontal brush motor 2 x 0,55 kw
Brush inverter 1,5 kw
Right brush motor 0,37 kw
Left brush motor (opt.) 0,25 kw
Conveyor motor 0,37 kw
Dust collection duct 3 x 90 mm
Dust collection 1500 m3/h
Net weight 260 kg
Dimensions 1450 x 1250 x 1410 mm

QuickWood System CD2 300 / CD4 200

CODE NO. CD4/300

For a perfect sanding and brushing

  • Rotating horizontal axes with adjustable speed by electronic inverter
  • Pressure rollers loaded with springs that ensure the sealing of workpieces during transport
  • Motorized roller conveyor with variable speed via invertor
  • Easily removable and inter changeable axes

Applications

  • Profiles
  • Rods
  • Frames
  • Uprights and transoms of doors and windows beads

Advantages

  • Reduced dimensions
  • Quality – price ratio of maximum convenience
  • Modular construction
  • Additional work units on all four side

Technical Specifications

CD 2 / CD 4
300/200

Height max. 100 mm
Width max. 300 mm
Length min. 380 mm
Horizontal brush motor 2 x 0,55 kw
Brush inverter 1,5 kw
Right brush motor 0,37 kw
Left brush motor (opt.) 0,25 kw
Conveyor motor 0,37 kw
Dust collection duct 3 x 90 mm
Dust collection 1500 m3/h
Net weight 260 kg
Dimensions 1450 x 1250 x 1410 mm

QuickWood System QT 1 Tiltable Sander Table With Brush

CODE NO. QT1

Model QT1 is equipped with a brush choice of QN with height 270 mm or quick flex with height 300 mm

  • Always ready to use for small series out of standard or special shapes
  • Ideal for sanding the raw and lacquered by using two different grits on the same brush (clockwise or anticlockwise rotation due to the use of the inverter)
  • Workpiece Support Table
  • On request you can have an inverter to adjust the speed, a height-adjustable table,work guides and dust extraction hood

Applications

  • Sanding the raw and sealer sanding of straight, curved and shaped profiles
  • Sanding of furniture in general both raw and painted

Technical Specifications

QT1-300

Height of Spindle 300 mm
Fixed Speed 900 rpm
Support Table 630×860 mm
Height of QN brush 270 mm
Height of Quick Flex brush 300 mm

QT 2 – Automatic Machine With Two Vertical or Horizontal Brushes For Sanding, Finishing of Curved Parts

CODE NO. CD4/300

Model QT2 has 2 vertical spindles 300 mm high as standard. As sanding tool we
recommend quick flex.

  • Speed of rotation of brushes from 200 to 1200 rpm, adjustable via electronic inverter Drive-in and out-of-feed rollers
  • Pressure rollers with special adjustable springs to adapt to curved shapes
  • Adjustable brush supports both in height and width to ensure the recovery of the brush wear and to adapt to the shape of the workpieces

Applications

  • Brushing of the raw and sealer sanding of curved and shaped pieces such as backs and legs of chairs and stools

Technical Specifications

Maximum working width 200 mm
Maximum working height 300 mm
Speed of brushes 100 – 1100 rpm
Through feed speed 1 – 10 m/min
Dimensions 900 x 1200 x 1500 mm
Weight 320 kg

QT 4 – For laminated shapes 2 or 4 sides in one pass

CODE NO. QMQT4

Model QT4 is as QT2 but with two horizontal sanding drums also equipped with Quick Flex. The lower sanding drums are fixed in the table and the upper ones are adjustable up and down.

Applications

  • Brushing of the rough and sealer sanding of curved and shaped pieces such as chair and table legs

Advantages

  • Brushing at 360 of the workpiece
  • Reduced machine size
  • Reduced sanding time

Technical Specifications

Main motors, kw 2 x 0,55
Revolutions per min. 200 – 1100
Horizontal drums, kw 2 x 0,37
Horizontal drums rpm 900
Length of spindle mm 300
Adjustable in width, mm 200
Adjustable in height, mm 300
Feed drive, kw 2 x 0,25
Feed speed, m/min 5

QuickWood System PRO- 1100/1400

CODE NO. QMPRO 1100V, QMPRO 1400V

Automatic Machine for Finishing and Sealer Sanding

New technique within the surface treatment of profiled, flat items

  • Finishing and sealer sanding
  • Alternative sanding tools can be mounted on remo vable spindles. See the various applications in our special leaflets
  • All machines are prepared for the treatment of wax and oil surfaces, structure brushing of white wood,
  • All machines are prepared for the treatment of wax and oil surfaces, structures brushing of white wood, sanding of MDF, veneer and solid wood
  • Simple operation of all adjustment possibilities and digital display for speed of spindles, rotation and conv e yor as well as for through feed height

Technical Specifications

Model Pro: 800 1100 1300 1400
Height max. mm 100 100 100 100
Length Infinity Infinity Infinity Infinity
Trough feed width, m/min 2 -12 2 -12 2 -12 2 -12
Spindle speed, rpm 200 – 1150 200 – 1150 200 – 1150 200 – 1150
Rotation speed, rpm 3 – 16 3 – 16 3 – 16 3 – 16
Spindle length ,mm 300 375 500 540
Number of spindles 4 8 4 8
Diameter of tool max. mm 350 350 350 350
Main motor, kw 2 x 1.5 4 x 1.5 2 x 2.2 4 x 2.2
Frequency alternator spindles, kw 4 7.5 5.5 11
Conveyor motor, kw 0.75 1.1 1.1 1.5
Vacuum pump, kw 7.5 11 11 2 x 7.5
Height adjustable, kw 0.45 0.45
Dust collection duct, m 4 x 140 4 x 170 4 x 170 6 x 170
Net weight, kg 1100 1800 1500 2100

Oscillating Cup Brush Sanding Machine

CODE NO. QMQRC 7/900, QMQRC 9/1300, QMQRC 14/1300

Features

  • Double / triple row of staggered sanding cups, with the rotation speed controlled by inverter
  • Side to side reciprocation of the sanding cups controlled by inverter
  • Sanding cups with r e verse direction, allow to be fitted with different grits of abrasive on both sides of the brush
  • High power vacuum belt for feeding and sealing of pieces
  • QRC 7/900-9/1300-14/1350

Applications

  • Wood: finishing of panels, doors and kitchen doors.
  • Metal: deburring double laser cutting
  • Stone: finish of ceramic surface and outdoor tables.

Advantages

  • The be vel effect of the edges, combined with the action of the rotating brushes, is very effective
  • Extremely easy and fast system to replace the sanding brushes, as Quickwood tradition
  • Extremely compact machine, to be easily integrated into tight spaces of existing production lines
  • Quality performance from a low priced machine

Technical Specifications

Model Pro: QRC 7/900 QRC 9/1300 QRC 14/1350
Number of cups 7 9 14
Brush’s diameter 250 mm 250 mm 250 mm
Number of segments for brush 12/36 12/36 12/36
Main motor 1,5 kw 2,2 kw 4 kw
Inverter size 1,5 kw 2,2 kw 4 kw
Rotation speed of brushes 200/900 rpm 200/900 rpm 200/900 rpm
Lifting motor 0,37 kw 0,37 kw 0,37 kw
Oscillation motor 0,55 kw 0,55 kw 0,55 kw
Number of oscillations 10-50 osc/min 10-50 osc/min 10-50 osc/min
Length of oscillation 110 mm 110 mm 110 mm
Conveyor motor 0,55 kw 0,75 kw 1,1 kw
Conveyor inverte 0,55 kw 0,75 kw 1,1 kw
Conveyor speed 2-12 m/min 2-12 m/min 2-12 m/min
Dust collection duct, diameter 4 x 90 mm 4 x 90 mm 6 x 90 mm
Weight 650 k g 950 k g 1500 k g
Dimensions 1785 x 1590 x 1900 mm 1785 x 1826 x 1900 mm 2100 x 1826 x h 1900 mm

QuickWood System PRO 1400/QRC

CODE NO. QMPRO 1400V

Automatic Brushing Machine Model For Kitchen Cabinet
Door And Entry Door Processing

Features

  • Rotating series with 4 or 8 cylindrical brushes combined with oscillating pads series ability to combine Quick flex smoothing brushes with penetrating brushes QN + QD

Applications

  • Kitchen and entrance doors and embossed
  • Panels in general
  • MDF, veneer, solid

Advantages

  • Maximum automatic sanding result
  • Continuous online installation
  • High productivity

Technical Specifications

Model Pro:PRO 1400 + QRC

No of cups 9 in 2 rows
Dia of cups 250 mm
No of radial slots 12/36
Working useful width 1400 mm
Cups rotation motor 2,2 kw
Inverter for cups motor 2,2 kw
Height control motor 0,37 kw
Oscillation motor 0,37 kw
Inverter for oscillation (from 20 to 60 strokes/min.)

QuickWood System PRO/1400BRUSHING/SANDING MODULE

  • It’s a new model on the market of brushing machines that has the exclusive feature to be equipped with 8 counter rotating drums, driven each one by 2 parallel axes lined on a rotating carousel.
  • This allows to ha ve the 100% of symmetrical brush effect so to ha ve softer homogeneous edges and surface. The 4 heads are equipped with 2 brushes each (so for a total of 8 brushes).
  • The brushes are of the type easily interchangeable by means of inserted nut-thread
  • The heads are to be positioned in height by means of electrical gear motor and push buttons and to be rotated at a variable speed of 3-16 rpm. The brushes ha ve also a variable speed of 300-1250 rpm.
  • The feeding of pieces is made by means of a vacuum high friction carpet. The feeding speed can be varied from 2 up to 12m/min.
  • The machine PRO1400 vacuum is equipped with 4 exhaust pipes for extraction of dus
  • The control box ha ve 4 digital visualizes to check easily the brush, the carousel’s and feeding’s speed which are variable trough inverter .

Technical Specifications

Working height 8-100 mm
Working length anyone
Working width 1400 mm.
Working speed 2-12 m./min.
Brushes revolution 380-1250 rpm
Carousel revolution 3-16 rpm
Motor power for brushes 4×2,2 Kw
Inverter for brushes 11 Kw
Motor power for carousel 1,5 Kw
Inverter for carousel 1,5 Kw
Gear motor power for feed 1,5 Kw
Vacuum pump power 11 Kw
Exhaust air 9.000 m3/h
Weight 2.100 Kg

QuickWood System QRC-9/1400 BRUSHING/SANDING MODULE

  • With 1 head oscillating with 2 rows of 9 (5+4) rotating cups in total.
  • All the cups rotate in the same direction and the speed is from 100 to 1200 rpm through an electronic inverter. The position in height of the sanding cups is made through gear-motor from 0 to 200 mm.
  • The head is oscillating 20 strokes a min. through a gear-motor and mechanical variable speed drive
  • The change and or refill of sanding paper is made very easily after rotation of the entire head on the axis to 90° over the carpet. The feeding carpet is the vacuum type with a high friction grip surface
  • The machine has a strong welded steel profile frame and is complete with windows and doors for safety and working access control. Regularly CE labelled and certified.

Technical Specifications

N° of cups 9 in 2 rows
Dia of cups 250mm
N° of radial slots 12/36
Working useful width 1400mm.
Cups rotation motor 2,2Kw
Inverter for cups moto 2,2Kw
Height control motor 0,37Kw
Oscillation motor 0,37Kw

N° 9 cups with relevant double face brushing paper